[permalink] [id link]
A bleeder resistor can usually be selected to prevent the screen voltage from getting out of control.
from
Wikipedia
Some Related Sentences
bleeder and resistor
If the normal load cannot be guaranteed to perform this function, perhaps because it can be disconnected, the circuit should include a bleeder resistor connected as close as practical across the capacitor.
Often, a high-resistance bleeder resistor is connected internally within the flyback transformer to ensure the charge is safely grounded when not in use, but many sets lack this, especially older models.
bleeder and can
These methods have the disadvantage that air is sometimes sucked back into the system via the bleeder valve threads, this can be alleviated to a degree by using Teflon tape on those threads.
The vacuum method can also draw in air via the bleeder threads, so the bubbles will never clear.
bleeder and be
The bleeder valve is designed to be top point of the fluid in the caliper.
bleeder and prevent
The other person opens the bleeder valve to let out fluid and air, then closes the valve after the pedal has landed ( to prevent air being sucked back in through the valve on the upstroke ).
bleeder and from
Carr pulled a broken nipple out of the bleeder valve and replaced both the nipple and the valve from new stock taken from Port Chicago's shop.
In Australia a first-time bleeder is banned from racing for three months.
This method is not recommended because with only one person there is no way to verify if indeed the fluid that is coming out of the bleeder valve has any air present, such as from a bad master cylinder or improper / incomplete bleeding.
Using Teflon tape on the bleeder threads will alleviate this issue and allow you to accurately determine when you have evacuated all air from the system.
bleeder and .
The workers maintain that entry of water through the plant's piping system during the washing of lines was possible because a slip-blind was not used, the downstream bleeder lines were partially clogged, many valves were leaking, and the tank was not pressurized.
The water, which was not draining properly through the bleeder valves, may have built up in the pipe, rising high enough to pour back down through another series of lines in the MIC storage tank.
On the afternoon of July 17, a bleeder valve on winch No. 4 required immediate repair.
The material is covered with release film, bleeder / breather material and a vacuum bag.
For example, the List of baseball jargon mentions base knock, bleeder, blooper, comebacker, daisy cutter, dying quail, flare, frozen rope, ground ball with eyes, nubber, salami, scratch hit, squibber, and other terms.
Dubbed " the little Aussie bleeder ", ( a play on the term " Aussie battler "), he satirised parochial Australian culture, media " personalities ", and egocentric talk show hosts.
Her sire was the good stallion, Gallinule who was also a roarer and bleeder.
Combined with the acoustic wave there is a general rise in pressure in the chamber caused by deliberately restricting the outlet with a small tube called the stinger, which acts as a bleeder, emptying the chamber during the compression / power stroke to have it ready for the next cycle.
Examples of these include: mez breeze, netwurker, data. h !. bleeder, ms post modemism, mezflesque. exe, Purrsonal Areah Netwurker and cortical_hacker.
Typically a length of clear tubing is connected to the bleeder valve and run to a container during the process, both to collect the toxic brake fluid and to better view the fluid and bubbles.
* Pump and Hold Method, One Person Option: This uses either a " one man " bleeder tool, consisting of a one way valve at the end of a length of tubing which is attached to the bleeder valve, or a special one way bleeder valve.
A specialized vacuum pump is attached to the bleeder valve, which is opened and fluid extracted with the pump until it runs clear of bubbles.
resistor and can
Thus in saturation mode, the FET behaves as a constant-current source rather than as a resistor and can be used most effectively as a voltage amplifier.
It is triggered by zero or negative input signal applied to Q2 base ( with the same success it can be triggered by applying a positive input signal through a resistor to Q1 base ).
* other varieties of op-amp include programmable op-amps ( simply meaning the quiescent current, gain, bandwidth and so on can be adjusted slightly by an external resistor ).
A moving coil galvanometer can be used as a voltmeter by inserting a resistor in series with the instrument.
If all four resistor values and the supply voltage () are known, and the resistance of the galvanometer is high enough that is negligible, the voltage across the bridge () can be found by working out the voltage from each potential divider and subtracting one from the other.
A meter can be used to read resistance by placing it in series with a known voltage ( a battery ) and an adjustable resistor.
When an unknown resistor is placed in series in the circuit the current will be less than full scale and an appropriately calibrated scale can display the value of the previously-unknown resistor.
It is also more accessible than speaking of the noise's power spectral density ( in watts per hertz ) since it is expressed as an ordinary temperature which can be compared to the noise level of an ideal resistor at room temperature ( 290 K ).
These frequency measurements can be easily taken, and thus the losses which appear as the voltage across the load resistor in the circuit are a periodic function of the applied magnetic flux with a period of Φ < sub > 0 </ sub >.
In some cases ( e. g., when the output of a TTL logic gate needs to be used for driving the input of a CMOS gate ), the voltage level of the " totem-pole " output stage at output logical " 1 " can be increased up to V < sub > CC </ sub > by connecting an external resistor between the V < sub > 3 </ sub > collector and the positive rail.
When a bias voltage and a load resistor are used in series with the semiconductor, a voltage drop across the load resistors can be measured when the change in electrical conductivity of the material varies the current flowing through the circuit.
Zero ohm resistors are made as lengths of wire wrapped in a resistor-shaped body which can be substituted for another resistor value in automatic insertion equipment.
A logarithmic potentiometer can also be simulated ( not very accurately ) with a linear one and an external resistor.
This short, intense pulse of current, typically 10 < sup > 9 </ sup >- 10 < sup > 10 </ sup > ion pairs, can be measured as a count event using the voltage developed across an external electrical resistor and can be in the order of volts, thus making further electronic processing simple.
The analog sampled filter will in its turn need yet another anti-aliasing filter, but this can often be implemented as a simple 1st order low-pass analog filter consisting of one series resistor and one capacitor to ground.
A wire can be represented as a low-value resistor
Adding a resistor, or better yet, an inductor, between the bridge and capacitor can ensure that current is drawn over a large portion of each cycle and a large current surge does not occur.
It can be modeled by a voltage source representing the noise of the non-ideal resistor in series with an ideal noise free resistor.
The noise generated at the resistor can transfer to the remaining circuit ; the maximum noise power transfer happens with impedance matching when the Thévenin equivalent resistance of the remaining circuit is equal to the noise generating resistance.
The noise source can also be modeled by a current source in parallel with the resistor by taking the Norton equivalent that corresponds simply to divide by R. This gives the root mean square value of the current source as:
1.226 seconds.