[permalink] [id link]
The mold disk is sometimes water-cooled, and often air-cooled with a blower, to carry away the heat of the molten type metal and allow the cast slugs to solidify quickly.
from
Wikipedia
Some Related Sentences
mold and disk
To assemble jar, put paper pattern B for base in bottom of mold and clay disk B on top.
These systems involve often multiple operations with implements such as a mold board, disk, and / or chisel plow.
Linotype mold disk, with a complete line of matrices and spacebands ready to be cast
Linotype mold disk, cut away to show the type metal pot
The justification vise holds the assembled line against the face of the mold disk.
The mold disk has rectangular openings which correspond to the width and thickness of the slugs ( cast lines ) to be made.
Behind the mold disk is the type metal pot, which contains molten type metal.
When casting is complete, the mold disk turns three-quarters of a turn counterclockwise to the ejector and knife block assembly.
The ejector is a rectangular rod that pushes the completed slug from the mold aperture in the mold disk.
As it emerges from the mold disk, the slug passes a set of knife edges in the knife block, which trims off any small irregularities in the casting and produces a slug of exactly the desired width and height.
The machine would then separate the mold disk ( carrying the freshly cast slug ), the metal pot, and the first elevator.
The mold disk would then turn to present the line at the ejecting position, in the process passing by a knife that trimmed the base of the slug to type height ( 0. 918 " on US machines ).
Depending on the model of machine, the mold disk could have 4 ( standard ), 6, or 2 molds, giving the operator his choice of line lengths and body sizes.
As the mold disk is turning, the first elevator simultaneously rises to its upper position and the space bands and matrices are vertically aligned in preparation for the second transfer.
For industrial casting of small parts using poured hot metal, a disk shaped mold is contained within a rotating drum, and molten metal is poured into the center.
A variation was a disk with a raised center, shaped much like a Bundt cake mold ; as the device sped up, people would slide downhill as well as outward.
mold and is
Allow project to stand for about five minutes ( if wooden press mold is a good antique, do not leave clay in too long as the dampness may cause mold to crack ).
While clay is still pressed in mold, press three equally spaced holes 1/4'' '' deep, using pencil eraser, in bottom of clay to allow for proper drying and firing.
A tax-free reorganization not complying with the merger or consolidation statutes of the states involved is difficult to fit into an `` operation of law '' mold.
Still more different from Bachofen's perspective is the lack of role permanency in Freud's view: Freud held that time and differing cultures would mold Athena to stand for what was necessary to them.
The glass is shaped when either fully molten, by casting, or when in a state of toffee-like viscosity, by methods such as blowing to a mold.
When all that is left is an organism-shaped hole in the rock, it is called an external mold.
An endocast or internal mold is formed when sediments or minerals fill the internal cavity of an organism, such as the inside of a bivalve or snail or the hollow of a skull.
This is a special form of cast and mold formation.
Sometimes the bioimmured organism is soft-bodied and is then preserved in negative relief as a kind of external mold.
... part of her does try to rebel against the restraints of a code of behavior that relentlessly attempts to mold her into a form to which she is not naturally suited.
It is covered with green mold and without fat and skin. Dalmatian ham is smoked and dried ham which is pressed and is very popular.
This process produces a distinctive flavor, but the mold layer is usually scrubbed or cut off the ham before being cooked and served.
Jell-O is also used as a substantial ingredient in a well-known dessert, a " Jell-O mold " the preparation of which requires a mold designed to hold gelatin, and the depositing of small quantities of chopped fruit, nuts, and other ingredients before it hardens and takes on its typical form.
Richard S. " Kinky " Friedman ( born November 1, 1944 ) is an American Texas Country singer, songwriter, novelist, humorist, politician and former columnist for Texas Monthly who styles himself in the mold of popular American satirists Will Rogers and Mark Twain.
He is currently starring in the Starz drama series Boss, as a fictional mayor of Chicago in the mold of Richard J. Daley which premiered in October 2011.
* casting – molten metal is poured into a shaped mold.
Along with Life and Matter, Forces is one of the three ' Pattern Spheres ' which together are able to mold all aspects of the physical world.
mold and sometimes
There is no unpleasant aroma, such as yeast, fungus, mold or paper, which sometimes occur with other chestnuts.
For prevention of mold growth in aqueous solutions, thymol is sometimes added ( The science of laboratory diagnosis By John Crocker, David Burnett ( relevant citation for thymol inhibits growth of fungi ).
In fact, the " cotton mold " Saprolegnia will sometimes infect fish, causing tufts of fur-like growth to appear on the body.
In other filters, sometimes called " organic filters ," wood chips or leaf mold may be used.
Her stories are in the New Wave mold, characterised by nonlinear, sometimes stream of consciousness narrative, intertextual references to the rest of Doctor Who and popular culture, and themes of unreliable narration.
The sand mixture is tamped down as it is added around the pattern, and the final mold assembly is sometimes vibrated to compact the sand and fill any unwanted voids in the mold.
* A powdery mildew disease of hops has sometimes been erroneously called blue mold.
It is sometimes possible to identify portraits that have been painted from death masks, because of the characteristic slight distortions of the features caused by the weight of the plaster during the making of the mold.
The genus contains some 50 species and bread mold is sometimes confused with species of Mucor or other species of Rhizopus like Rhizopus oryzae.
Redecos are an extremely popular way to create exclusive toys, allowing the new toy to look drastically different from the original, sometimes representing a different character, entity or item, without having to pay for an entirely new mold.
It is sometimes found in soil and grain, but the mold is most often detected in cellulose-rich building materials from damp or water-damaged buildings.
0.317 seconds.