We assume for this illustration that the size of the land plots is so great that the distance between dwellings is greater than the voice can carry and that most of the communication is between nearest neighbors only, as shown in Figure 2.

In Figure 2, the points in the network are designated by a letter accompanied by a number.

In any social system in which communications have an importance comparable with that of production and other human factors, a point like f in Figure 2 would ( other things being equal ) be the dwelling place for the community leader, while e and h would house the next most important citizens.

The anode plug ( Figure 2 ) was inserted into a carbon anode holder.

A band viscometer is shown in Figure 2.

As can be seen from Figure 2, an extensive area was covered by this aerosol.

Some of the features of the top portions of Figure 1 and Figure 2 were mentioned in discussing Table 1.

The data for boy 34 appear in Figure 3, and for girl 2 in Figure 4.

For example, arrow 17 in Figure 3 portrays the proximal radial epiphysis for boy 34, whereas the same epiphysis for girl 2 is portrayed by arrow 18 in Figure 4.

The Skeletal Age curve in the lower portion of Figure 2 shows that slowing may have occurred for her during the prepubescent period.

In the gastrocnemius and biceps there were many swollen and homogeneous necrotic fibers such as that shown in Figure 2.

Figure 2 is a graph of the mean achievement scores of each group.

The pilot plant was equipped with a 3-hp. turbine aerator ( Figure 2 ).

Figure 2, above, shows the aging properties of urethane foams as determined by the percent of change in tensile strength during exposure to ultra-violet light.

This motion was evidently not due to parallax, for the reasons given in the discussion of Figure 2, and neither was it due to observational errors.

Figure 2.

Deformation implies the change in shape and / or size of the body from an initial or undeformed configuration to a current or deformed configuration ( Figure 2 ).

In the Lagrangian description, the motion of a continuum body is expressed by the mapping function ( Figure 2 ),

Figure 2: Various semiconductor diodes.

Figure 2: Measuring schedule performance without knowledge of actual cost.

Figure 2 shows the EV curve ( in green ) along with the PV curve from Figure 1.

Figure 1: Basic Bipolar junction transistor | BJT astable multivibrator

Figure 2: Basic BJT monostable multivibrator.

Figure 3: Basic BJT bistable multivibrator ( suggested values: R1, R2 = 1 kΩ R3, R4 = 10 kΩ ).

Figure 1: Basic NPN common-base circuit ( neglecting biasing details ).

Figure 1: Basic NPN common-emitter circuit ( neglecting biasing details ).

MicroScript is based on, and makes extensive use of, the TRON Basic Text Editor, and Basic Figure Editor.

Figure 1: Basic NPN common-collector circuit ( neglecting biasing details ).

Figure 1 – Basic elements of the diagrammatic system commonly used to represent Force Dynamic patterns.

Figure 1: Basic example of the isolobal analogy.

Figure 1: Basic N-channel common-gate circuit ( neglecting biasing details ); current source I < sub > D </ sub > represents an active load ; signal is applied at node V < sub > in </ sub > and output is taken from node V < sub > out </ sub >; output can be current or voltage

Figure 1: Basic N-channel JFET common-source circuit ( neglecting biasing details ).

Figure 2: Basic N-channel JFET common-source circuit with source degeneration.

The Figure Skating Club of Memphis uses the ice rink during the hockey season to provide Learn to Skate clinics, USFSA Basic Skills Classes, and freestyles for area figure skaters.

Figure 1 provides a schematic diagram of the components of a typical vapor-compression refrigeration system.

The Figure 1 below shows the components of a typical surface resonant vibrator.

Consider a point in a continuum under a state of plane stress, or plane strain, with stress components and all other stress components equal to zero ( Figure 7. 1, Figure 8. 1 ).

Figure 8. 2-Stress components at a plane passing through a point in a continuum under plane stress conditions.

The principal directions ( Figure 8. 3 ), i. e. orientation of the planes where the shear stress components are zero, can be obtained by making the previous equation for the shear stress equal to zero.

Considering the steps of Patton and Sawicki model as in Figure 1 above, this paper only follows components 1 to 5 of the rationalist policy analysis model:

PEDOT-PSS ( Clevios P ). As an example of a static application, poly ( 3, 4-ethylenedioxythiophene )- poly ( styrene sulfonate ) ( PEDOT-PSS ) product Clevios P ( Figure 7 ) from Heraeus has been extensively used as an antistatic coating ( as packaging materials for electronic components, for example ).

The different components of production are displayed in the Figure 1.

Figure 3: Bipolar current mirror: i < sub > 1 </ sub > is the reference current and i < sub > 2 </ sub > is the output current ; lower case symbols indicate these are total currents that include the DC components

To construct the Mohr circle of stress for a state of plane stress, or plane strain, first we plot two points in the space corresponding to the known stress components on both perpendicular planes, i. e. and ( Figure 1 and 2 ).

As an example, let's assume we have a state of stress with stress components,, and, as shown on Figure 2.

Figure 1: Flow Chart displaying the relationship of carbon components

Figure 1 shows the simplest grating configuration, where long-wavelength components travel a larger distance than the short-wavelength components ( negative dispersion ).

The experiment requires a few simple components ( see Figure 1 ): a cylindrical magnet, a conducting disc with a conducting rim, a conducting axle, some wiring, and a galvanometer.